12.01.2021

2gr Fe Race Engine

77

Makishima yuusuke voice actor. To increase the 2GR-FSE 3.5L engine size to 4L, the bore would need to be 96 mm and the stroke 92 mm. Below is how we achieved it.

Note:

After using this engine for a while the 1GR crankshaft was replaced with the 2GR to make the engine 3.6L. This was done as the engine had piston slap noise. I did not like this so made the change. The 3.6L engine made the same power at 22 psi boost.

2GRFE Engine Sort by Featured Best Selling Alphabetically, A-Z Alphabetically, Z-A Price, low to high Price, high to low Date, new to old Date, old to new Tach Adapter - Rat2. Approximate build time: 7 weeks from order date All MWR built 2GR engines include: - Brand new OEM oil pump, gaskets and seals throughout - Wiseco forged pistons - MWR main and rod bearings - Crankshaft custom balanced - Competition 3-angle valve job - Expert machine work and assembly.

To get the required 96 mm bore, the block was sleeved using Nissan TD42 (four cylinder diesel) engine sleeves.
Sleeves have a flange on top that is used for stopping the sleeves from moving. Original water bypass between bores is retained.

Pistons were made by Special Piston Services in Australia. The pin height is 1.1' (27.94 mm). The bowl in the pistion is 29 cc to give a 9.0:1 compression ratio.

The conrod is from the Lexus 1UZ-FE V8 engine.

The big end of the 1UZ conrods are 2mm (0.080') wider then the 2GR-FSE. We machined the rods to the correct width. The small end does not need to be machined.
To get the 4L engine size we needed a 92 mm stoke. We used the Toyota Hilux 4L 1GR-FE crankshaft and de-stroked it down to the 92 mm. This was possible as the 1GR-FE big ends are 3 mm bigger diameter. We offset ground them to get the required stroke.
The mains 1GR-FE are 72 mm. These were reduced the the 2GR-FSE 61 mm diameter.
The bolt pattern for the flywheel is a bigger diameter and so it the rear main seal. You can see this in the picture.
Top crankshaft is the 1GR-FE after modifications to suit the 2GR-FSE block. The bottom is the stock 2GR-FSE. Only difference now is the bigger seal diameter.

To fix the bigger rear main seal problem, we made a new seal plate with the 2GR-FSE bolt pattern and a hole for the bigger 1GR-FE seal.

1UZ-FE bearings are 19mm wide. As we machined the conrods 2 mm narrower we also machined the bearings narrower. They are now 16mm wide.
The jig we used to machine the bearings narrower.
Counter weights had flats cut on them to clear the bottom of the pistons. This caused balancing problems and Mallory metal was needed in the counter weights on both ends of the crank.
Block assembled
Crank turns and nothing hits.:-)
Finished and ready to fit in the car.
2GR-FSE Flywheel was re-drilled to suit the bigger bolt pattern on the 1GR-FE crankshaft.

The Toyota GR engine is an open deck V6 piston with a 60° die-cast aluminium block and aluminium DOHC cylinder heads. The engine was first used in the Evora as a 3456cc normally aspirated engine and then it was supercharged for the Evora S and the new Exige V6.

track-group have extensive experience of this engine in track and race cars and our dyno is fully configured to run in and power test these engines. We can offer brand new crate engines either standard or with a number of upgrade options including improved pistons & connecting rods. We can also offer rebuild and upgrade services for the 4.0l NA GT4 Evora engine including the new pistons, camshafts and power upgrade.

Toyota 2gr Fe Engine Specifications

track-powertrain can also provide these engines configured with aftermarket ECU and electronics options, improved exhaust systems, camshafts and other improvements for significant horsepower gains.

2gr Fe Race Engine

2gr Fe Toyota Engine Specs

Product Categories

2gr-fe Race Engine

Engine

Toyota Engine 2gr Fe

  • Engine
  • Lotus Performance
  • Motorsport Fluids
    • Motul
  • Performance Friction
  • Race Logic